Meters

From nftables wiki
Revision as of 09:18, 15 April 2018 by Duncan (talk | contribs) (No longer need to get iptables from the git tree for hashlimit translate support)
Jump to navigation Jump to search

Meters

This feature used to be known as flow tables before nft v0.8.1.

Since Linux Kernel 4.3 and nft v0.8.1 nftables supports this feature.

Meters provide a native replacement for the hashlimit match in iptables, however, meters are a lot more flexible since you can use any selector, one or many through concatenations.

Using meters

The following commands create a table named filter, a chain named input which hooks incoming traffic and a rule that uses a meter:

% nft add table filter
% nft add chain filter input {type filter hook input priority 0\;}
% nft add rule filter input tcp dport 22 ct state new meter ssh-meter { ip saddr limit rate 10/second } accept

In this example we create a rule to match new ssh (port 22) connections, which uses a meter named ssh-meter to limit the traffic rate to 10 packets per second for each source IP address. The available time units on limits are: second, minute, hour, day and week.

Note that meters must have a name, so you can list its content.

You can also use concatenations to build selectors:

% nft add rule filter input meter cnt-meter { iif . ip saddr . tcp dport timeout 60s counter }

This rule counts incoming packets based on the tuple (input interface index, IP source address, TCP destination port), the counters are dropped after 60 seconds without update.

Listing meters

To list the content matched by the meter use:

% nft list meter filter cnt-meter
table ip filter {
	meter cnt-meter {
		type iface_index . ipv4_addr . inet_service
		flags timeout
		elements = { "wlan1" . 64.62.190.36 . 55000 expires 38s : counter packets 2 bytes 220, "wlan1" . 83.98.201.47 . 35460 expires 39s : counter packets 10 bytes 5988, "wlan1" . 172.217.7.142 . 43254 expires 46s : counter packets 1 bytes 98}
	}
}

Doing iptables hashlimit with nft

Meters replace iptables hashlimit in nft. From iptables v1.6.2 onward, you can use the tool iptables-translate to see how to translate hashlimit rules.

Almost all hashlimit options are available in nft, starting with --hashlimit-mode, it is replaced by the selector in a meter. All modes are available except no mode, a meter demands a selector, an iptables rule without hashlimit-mode isn't supported in nft. A simple rule translation is:

$ iptables-translate -A INPUT -m tcp -p tcp --dport 80 -m hashlimit --hashlimit-above 200/sec --hashlimit-mode srcip,dstport --hashlimit-name http1 -j DROP
nft add rule ip filter INPUT tcp dport 80 meter http1 { tcp dport . ip saddr limit rate over 200/second } counter drop

Notice that a meter is named, like hashlimit, and using multiple hashlimit-modes is similar to using a concatenation of selectors. Also, --hashlimit-above is translated to limit rate over, to simulate --hashlimit-upto just omit or replace over with until in the rule.

The options --hashlimit-burst and --hashlimit-htable-expire are translated to burst and timeout in a meter:

$ iptables-translate -A INPUT -m tcp -p tcp --dport 80 -m hashlimit --hashlimit-above 200kb/s --hashlimit-burst 1mb --hashlimit-mode srcip,dstport --hashlimit-name http2 --hashlimit-htable-expire 3000 -j DROP
nft add rule ip filter INPUT tcp dport 80 meter http2 { tcp dport . ip saddr timeout 3s limit rate over 200 kbytes/second burst 1 mbytes} counter drop

This rule shows how timeout and burst are used in a meter, also notice that meters, similarly to hashlimit, accepts limiting rates by bytes frequency instead of packets.

Another hashlimit option is to limit the traffic rate on subnets, of IP source or destination addresses, using the options --hashlimit-srcmask and --hashlimit-dstmask. This feature is available in nft by attaching a subnet mask to a meter selector, attach to ip saddr for source address and to ip daddr for destination adress:

$ iptables-translate -A INPUT -m tcp -p tcp --dport 80 -m hashlimit --hashlimit-upto 200 --hashlimit-mode srcip --hashlimit-name http3 --hashlimit-srcmask 24 -j DROP
nft add rule ip filter INPUT tcp dport 80 meter http3 { ip saddr and 255.255.255.0 limit rate 200/second } counter drop

This rule will limit packets rate, grouping subnets determined by the first 24 bits of the IP source address, from the incoming packets on port 80.

The remaining options, --hashlimit-htable-max, --hashlimit-htable-size and --hashlimit-htable-gcinterval don't apply to meters.